Media Library / Images

Slimline 21 red

Quality petrol pump hose for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B 30 (BIO Type up to B 100). Meets weights and measures regulations, see overleaf. Cold flexible down to - 30° C / - 22° F (LT-type down to - 40° C / - 40° F). Corresponds to EN 1360 and EN 13483.

Underwing refuelling, HD-C hose assembly

Hydrant dispenser

ZVF 50 helicopter refuelling with HD-C hose assembly

France

Hot stamping process, TW coupling part

Maintenance at the petrol station

GasGuard LPG nozzle GG30

4-slot design to facilitate connection of the nozzle to the vehicle fill point. New nose piece design to reduce the released gas upon valve closure, incorporating improved gas release method to minimise the risk of splash back.

Storz Safety Coupling SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.

Adapters / couplers for vehicles fighting dangerous goods incidents:

Adapter for Rail Tanker 51/2" connection KWZ SS/Vi x VK 50 SS/Vi

LMD 32 Blue Band solvent hose

without helix

RD 50 seal, NBR blue

for foodstuff threaded couplings

RN 2 x 21/2" SS

Reducing nipple

FSH flame protection cover for ERV rubber expansion joints

Use e.g. in ship engine rooms

ERV-ROTEX expansion joint, inhouse emergency power generator

ERV-G 150.TW, ERV-G 80.TW

Aircraft refueller

LNG Refuelling

LNG Nozzle 'N-LNG' coupled to fuel, LNG 25 fill hose assembly, vent hose assenbly with 'VC-LNG'

Hose assemblies

for dangerous goods: ELAFLEX quality

ZVG 2 ACME nozzle for L.P. Gas / Autogas

LPG nozzle for vehicle refuelling with liquefied petroleum gas (propane, butane and mixtures) up to 50 l / min. Working pressure 25 bar. Test pressure 40 bar. Burst pressure > 100 bar. Temperature range - 25° up to + 70° C, 'LT'-Type down to - 40° C.

DDC-V 50 SS F

MannTek Dry Disconnect Coupling, DN 50, stainless steel, with flange connection

Elaflex Cam and Groove Couplings ('Camlock'): AMKX 50 EASY

EASYLOC stainless steel coupler to EN 14420 - 7, with lever arrest. Picture shows the version as one-piece coupler with integrated hose tail and Spannfix stainless steel clamp

ERV-G

with vacuum support spiral

AVKC 50 Ms

'Camlock' brass steel male part to EN 14420 - 7 with hose tail and Spannloc clamps

CBC-PERC 100

Cryogenic Breakaway Coupling "PERC" for LNG after pneumatic separation

ZV 500

High performance manual operated dispensing nozzle with 'TW' coupling MK 50 for Diesel, fuel, oils, petroleum

LPG Autogas dispenser, ZVG 2 ACME nozzle, LPG 16 dispensing hose

Requirements to a Hose

(English)

ZVA Slimline 2 GR

Automatic nozzle with vapour recovery, flowrate up to 45 l / min.

MK-A 80 SS, TW female coupler with Active Safeguard Lever, VB 80 SS

Pull slider to unlock

ZVA "LT" nozzles

Low Temperature type -40° C for cold regions

BK 3 SS

Cap with 3" female BSP thread, stainless steel

Unloading petroleum products at the service station (road tanker to UST)

Connection offset UST filling point: LG 3" hose assembly for gravity discharge, LTW 50 hose assembly for vapour balance