Media Library / Images

Elaflex hose assemblies

Hose fittings: threaded, flanged, quick couplings, Dry Disconnect Couplings

Rubber Expansion Joint ERV-CR 80.16

CR Expansion Joints for cold and warm water, swimming pool water, sea water, waste water (weakly sour or alkaline) also oil containing, cooling water with protective oils against corrosion, lubricating oil, grease and air, compressed air. Temperature range (depending on medium) - 25° C up to + 90° C, temporarily up to + 100° C. Electrically non-conductive.

Adapter: MK 50-45° SS x VK 50 SS

The lever is bent to enable lever arrest (safe position when coupled)

H2 Cover Hose 'CH-H2 38'

Safety Break Thread

BD 63 Hose Beads

to EI 1522 standard - notably improve handling as they reduce friction against the tarmac. They additionally protect against hose abrasion. 'BD' Hose Beads are highly break resistant, contain no bolts or nuts, can be easily assembled or disassembled and are suitable for reeling.

Composite hose assemblies with 'COPSAFE' , suitable for COP systems (cross-over prevention)

electrical conductivity

Connection road tanker to trailer: LTW hose assembly, DDC Dry Disconnect Coupling

Unloading petroleum products at the service station (road tanker to UST)

LG 3" hose assembly for gravity discharge, LTW 50 hose assembly for vapour balance

SG 1" 1x0 Al

Sight Glass, to EN 13617-1, DN 25, for installation between petrol station nozzle and hose assembly, or mounting on the dispenser. For the visual control of bubble-free dispensing and fuel colour (e. g. for premium fuels). Suitable for all standardised gasoline and diesel fuels according EN 589 + EN 590, including ethanol or biodiesel content, also Avgas and Jet-A1.

Sand casted products to your design

In our modern foundry we can produce complex sand casted aluminium, bronze and gunmetal products to your requirements.

MB 80 SSE

TW dust cap of stainless steel, surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

GasGuard LPG nozzle GG1EH

used for industrial refueling / attended refueling. With hybrid nose piece − low lever force. Release volume on valve closure: 1,7 cm³.

ZVA Slimline 2 GRVP, Coax hose assembly

With integrated vapour insert EK 096. For dispensers with single fi lling point or dispensers with integrated 'On / Off ' valve. The vapour return rate is regulated within the dispenser.

ELAFLEX Hamburg

Aerial view (left to right): Technical dept., small aisle stock, stock with loading ramps

ZVG 2 ACME nozzle for L.P. Gas / Autogas

LPG nozzle for vehicle refuelling with liquefied petroleum gas (propane, butane and mixtures) up to 50 l / min. Working pressure 25 bar. Test pressure 40 bar. Burst pressure > 100 bar. Temperature range - 25° up to + 70° C, 'LT'-Type down to - 40° C.

ELAFLEX Hamburg

Assembling ERV medium DN

V 19-3/4" NPT

Male ferrule hose coupling EN 14424 stainless steel, reusable. Slimline 19 SF (sulphur free) hose, black.

Rubber Expansion Joint ERP 80.16

RED SPOT expansion joints for sanitary installations, highly flexible, for cold and warm water, pool water, sea water, drinking water. Temperature range (depending on medium) - 40° C up to + 90° C, temporarily up to + 120° C. Electrically dissipative.

MK 50 SSE

TW female coupler. Material: stainless steel with universally resistant PFA coating (red)

FWS composite hoses / hose assemblies

Type FWS PP with female threaded fitting, Type FWS PTFE with stainless steel flange

AMKX 50 SS

'Camlock' stainless steel steel coupler to EN 14420 - 7 with hose tail and Spannfix clamps

ERV ZSS:

Tied Flanges – Tie rods with inner and outer limitation

Offshore FSRU (Floating Regasification Unit), connector for gasoil sludge / seawater

DDC-V 150 F

ELAFLEX Hamburg

Coax hose assembling, colours

ELAFLEX Hamburg

Hose assemblies, marking after testing on the fitting

ELAFLEX Hamburg, large new narrow aisle stock 2018 for hoses

ZVF 50 JET

Manual aviation fuelling nozzle for overwing service. Flowrate up to 400 ltr. / min. (85 IGM – higher flowrates are possible). Size DN 50. Working pressure 10 bar (140 psi). Temperature range -40° C up to +55° C

ELAFLEX Tanktechnik, Production Plettenberg / Germany

Swivel assembling

Oasis Engineering Ltd, New Zealand (CNG refuelling products)

Production Picture 7

DDC-M 50 F Aseptic

MannTek Dry Disconnect Coupling with Aseptic flange