Media Library / Images

Unloading petroleum products at the service station (road tanker to UST)

LTW hose assembly, MK 80-32° Ms couplers with bent lever. The lever shall always be fully closed for safety reasons. For applications with limited room.

ZVG 2 K (Korea)

uncoupling from J 15 filler connection

Universal hose assembly UTS 50 with VC 50 SS / SS

Storz Safety Couplings Type SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.

Slimline 21 green

Quality petrol pump hose for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B 30 (BIO Type up to B 100). Meets weights and measures regulations, see overleaf. Cold flexible down to - 30° C / - 22° F (LT-type down to - 40° C / - 40° F). Corresponds to EN 1360 and EN 13483.

Tank storage, mixer: LTW hose assemblies

Underwing refuelling, HD-C, aircraft dispenser

Oasis PM104 Priority Panel / Manifold, for CNG

ZVA Slimline 2 GR, Coax hose assembly

Automatic nozzle with vapour recovery, flowrate up to 45 l / min.

ERV-OR

"Orange Band" Rubber Expansion Joints for L.P. Gas, road tanker

Boat refuelling, ZVA 25

VB 100 SSE

TW dust plug of stainless steel, surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

ERV-R

"Red Band" Rubber Expansion Joints / ship engine room

ZVF 50 helicopter refuelling with HD-C hose assembly

France

ARK 19 Safety Break including BS 19 Break Sleeve

Safety Break (Hose Break) for installation to LPG Autogas dispensers. Reassembly on site without tools

Filling of Heating Oil Tanks: Adapter KR 50-21/2"

for difficult to reach filler inlets

Tecnopal 38

Chemical hose to EN 12115 for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).

LNG Refuelling

LNG Safety Break for installation on LNG dispensers SB-LNG FL-J

Rubber Expansion Joint ERV-GS HNBR 80.16

YELLOW STEEL HNBR expansion joints for petroleum based products, DIN EN fuels up to 50 % aromatic content, cooling water with oily anticorrosion additives, lubrication and hydraulic oil, seawater. Very good aging, weathering and ozone resistance. Temperature range (depending on medium) - 35° C up to + 100° C, temporarily up to + 120° C. Fire resistant to ISO 15540 up 30 min. at + 800° C. Electrically dissipative.

IBC loading and unloading

MannTek DDC-M 50, FWS 50 PTFE

ROTEX 80.16 ZS 2

Tied Flanges – Type ZS, Tie rods with outer limitation in rubber bushings

LNG Refuelling

Venting the tank with Vent Coupling 'VC-LNG'

Lightweight Gravity Discharge Road Tanker Hose LG 4"

with TW couplings

ERV-GR 80.16 ZS 2

GREEN BAND Rubber Expansion Joint with "ZS" limiter (tie rods with outer limitation in rubber bushings)

Production TW couplings

ELAFLEX HIBY Tanktechnik, Production Plettenberg / Germany

Assembling ZVA

ZVF 50 JET

ELAPHARM Type EPH-OHM G

electrically conductive 'OHM/T', with light grey cover, to EN 16820, Type A. FDA conform, homogeneous elastomer hose construction with smooth, black PTFE liner. Clamp fittings, lining flared (free of dead spaces).

ZVA Slimline 2 GR

blue scuffguard, blue produc sleeve, guard no. 4

Integrated Diesel Drip Catcher for ZVA Slimline 2